Industrial Machinery

KraussMaffei Extrusion Pushes Single-Stage PVC InlineMixing for Roofing Membranes

Anja LindqvistNovember 17, 20265 min read3 views

At a glance

  • The continuous route feeds powders, liquids and fillers straight into a twin-screw extruder, dropping the separate hot-cold mixing and dryblend storage step the company says accounts for much of the cost.
  • KraussMaffei Extrusion has developed PVC InlineMixing, a continuous single-stage process that replaces batch dryblend preparation for PVC roofing membranes. The company reports energy savings of up to 75 percent depending on formulation, system parameters and site, and says one industrial line with two extruders and two calenders already runs at 1,800 kg/h.
Cutaway illustration of a twin-screw extruder with gravimetric feeder hoppers and liquid dosing lines mounted on the barrel, feeding a flat die and calender rolls that carry a continuous PVC membrane sheet.

KraussMaffei Extrusion has developed a continuous single-stage process, marketed as PVC InlineMixing, for making PVC roofing membranes. The approach removes the separate batch mixing stage that normally sits ahead of extrusion, a step the company identifies as a major driver of energy, space and labour cost in conventional membrane plants.

In the established two-stage route, PVC powder, plasticizers, additives and fillers are combined batchwise in a hot-cold mixer combination to produce a dryblend. That blend is cooled, held in intermediate storage and only then plasticized in a twin-screw extruder and formed into membrane. With PVC InlineMixing, all solid and liquid components are metered directly into the extruder by gravimetric dosing systems in exactly the required proportions, so compounding and plasticizing happen in a single pass.

Where the savings come from

According to the company, the main cost advantages follow from eliminating the separate heating-cooling-mixing combination. No investment is needed in that hardware, and the material is heated only once. Energy consumption, and therefore energy cost, is reduced by up to 75 percent depending on the formulation, the system parameters and the location of the plant.

Removing the standalone mixing step also shrinks the footprint of the whole line and lowers labour requirements compared with a system built around dryblend premixing. Maintenance spending is described as lower as well, because wear parts for the heating-cooling mixer are no longer required. The combination of reduced capital expenditure and reduced operating costs is presented as the basis for an improved overall cost picture and a fast payback on the system.

Formulation changes during operation

The continuous concept is also argued to be more flexible. Formulation adjustments and colour changes can be carried out directly during operation through the integrated control system, which the company says removes the time-consuming preparation and interim storage of separate dryblend batches.

Christopher Bartel, Head of Sales Flat & Foam at KraussMaffei Extrusion, framed the change as a competitive matter for membrane producers: lower production costs, greater flexibility and more efficient manufacturing would let them respond faster to new requirements and adjust formulations within the running process while cutting both energy use and capital spending.

Validation on the ZE 65 BluePower

The process was developed at the KraussMaffei Extrusion Technology Center in Laatzen and validated using industrial roofing membrane formulations. The trials ran on a co-rotating twin-screw extruder from the ZE 65 BluePower series, equipped with loss-in-weight feeders for all solid components and with multiple liquid feeders for free-flowing ingredients.

That extruder series has a Da/Di ratio of 1.65, and the company states that the pairing of high torque with large free volume opens a wide process window for running different formulations. The tests confirmed good gelation of the PVC and high product quality, with the mechanical properties and weldability of the resulting membranes meeting industrial requirements across several formulations.

Bartel said the results show the potential of PVC InlineMixing for industrial roofing membrane production, and that the Technology Center works with customers to test their own formulations under production-relevant conditions, optimize the process and establish a basis for industrial implementation.

Already in an industrial line

The process is not confined to trials: it is already in use in an industrial production line for PVC roofing membranes. The reference plant reaches a total throughput of 1,800 kg/h using two extruders and two calenders, and processes PVC, additives and fillers together with the resulting edge trimmings continuously into finished membrane.

KraussMaffei Extrusion positions the development as a way to combine high product quality with a leaner production sequence, aimed at more cost-effective and more flexible output of PVC roofing membranes.

Reported by Anja Lindqvist, Polymer and Specialized Machinery Analyst.