Renewable Energy

Emulsion Buffer Layer Reduces Screen-Printing Damage in Copper-Plated HJT Cells

Nadia PetrovaNovember 15, 20265 min read0 views

At a glance

  • Chinese researchers link degradation to worn mesh knuckles and report a 4.7% emulsion coverage design that limits lifetime losses during photoresist printing.
  • A China-based research team has identified progressive wear of screen mesh knuckles as a key cause of screen-printing degradation in copper-plated HJT solar cells. Its proposed emulsion buffer layer, at 4.7% coverage, reduced minority-carrier lifetime degradation after 10,000 printing cycles while maintaining acceptable photoresist uniformity, according to the study.
A conceptual cross-section shows a screen-printing mesh above a silicon heterojunction wafer, with an emulsion buffer layer separating the mesh knuckles from the cell surface.

Screen printing is widely used to form metal contacts on solar cells, but the process can degrade device performance. The problem is particularly relevant to copper-plated silicon heterojunction (HJT) cells, which promise lower metallization costs and less reliance on silver. A research team in China investigated the degradation mechanism in these cells and tested a method to mitigate it, reporting the results in Solar Energy.

HJT cells depend on sensitive passivating contact structures. The mechanical pressure and thermal treatment involved in screen printing can damage those layers, raising recombination losses and lowering conversion efficiency. Understanding the damage pathway is therefore necessary for optimizing metallization without sacrificing cell performance.

Direct mesh contact during photoresist printing

Corresponding author Lang Zhou explained that printing photoresist for HJT cells differs fundamentally from conventional screen printing of silver paste. In silver paste printing, screen openings cover only 2–5% of the total area, while an emulsion layer covers the rest and prevents direct contact between the mesh and the wafer. Full-area photoresist coating typically uses a screen without emulsion coverage so that resist can be deposited uniformly across the wafer. As a result, the mesh contacts the wafer directly and extensively during every printing cycle.

The team said earlier investigations had shown conversion efficiency falling from 26.2% to 25.7% over 15,000 consecutive printing cycles in commercial solar cell production. Open-circuit voltage and fill factor accounted for most of the loss, while short-circuit current density and electrical resistance remained largely unchanged. Minority carrier lifetime degradation rose from 0.61% with a new screen to 11.0% after 15,000 cycles.

Knuckle wear and hidden interface damage

Using three-dimensional confocal microscopy, the researchers identified progressive wear of the screen mesh knuckles as the main cause. As the knuckles wore down, their contact area with the wafer increased, placing greater mechanical stress on the passivation layers beneath. Scanning electron microscopy showed no visible surface scratches, but photoluminescence measurements indicated increased recombination losses. The researchers interpreted this as evidence of damage to the amorphous silicon/crystalline silicon interface.

Emulsion buffer and coating trade-off

To prevent direct contact between the mesh and the wafer, the team developed an emulsion buffer layer and evaluated six patterns with emulsion coverage ratios from 2.9% to 16.6%. The results revealed a trade-off: greater emulsion coverage reduced mechanical damage but impaired photoresist coating uniformity and ink distribution. A coverage ratio of 4.7% provided the best balance, limiting minority carrier lifetime degradation to 0.41% after 10,000 printing cycles while maintaining relatively good coating uniformity.

The researchers attributed the improvement to the emulsion layer blocking direct contact between the screen mesh and wafer, thereby reducing cumulative mechanical damage to the sensitive passivation layers. Zhou said the findings show that a relatively simple change to screen design can substantially mitigate printing-induced degradation, offering a practical route to improving manufacturing reliability for copper-plated HJT cells.

Copper metallization gains attention

The work comes amid growing interest in copper as an alternative to silver contacts in HJT cells. In April 2026, researchers at China’s Nankai University reported a silver-free HJT cell with 25.2% efficiency using plasma-induced interface engineering and copper electroplating. That approach addressed adhesion, contact resistance and stability challenges at the indium tin oxide interface.

Separately, scientists at Germany’s Forschungszentrum Jülich achieved 23.08% efficiency in a fully copper-metallized HJT cell. The silver-free device showed a relatively small efficiency penalty compared with its silver-metallized counterpart, while cells combining silver-copper paste on the front side with silver contacts on the rear reached 23.95%. Those results underline copper’s potential to reduce silver consumption, although further improvements in processing and electrical performance are still needed.

Reported by Nadia Petrova, Nickel, Titanium and Refractory Metals Analyst.