The UK is partner country at Formnext in Frankfurt from 17 to 20 November, arriving with a long record of additive manufacturing invention and a much shorter one of turning it into production. The question running through the founders, machine builders and university commercialisation staff interviewed for this series is not whether Britain can invent, but who ends up making the parts.
A record of invention, a question of production
The historical comparison offered is Portsmouth. Henry VII ordered a dry dock there in the 1490s, and during the Napoleonic Wars the Royal Navy bought about 100,000 wooden pulley blocks a year; HMS Victory alone needed more than a thousand. In 1803 the first block-making machines designed by Marc Isambard Brunel and built by Henry Maudslay began operating at the dockyard, and by 1808 its 45 machines produced 130,000 blocks. The invention gets the billing, but the Navy knew what it used, in which sizes and quantities, and could watch the first machines work before committing to the next set.
Wayland Additive's chief executive, Will Richardson, points to metallurgy and materials science at Sheffield, Birmingham, Cambridge and Oxford and to the Henry Royce Institute. His company grew out of a team with electron-beam experience in semiconductors, and in October a Calibur3 metal system left its Huddersfield facility for the University of Innsbruck, where researchers will study difficult materials including those intended for high temperatures. Britain built and exported the machine; some knowledge of what it can do will accumulate in Austria.
The numbers are plentiful but incomplete. The European Patent Office counted 1,925 international patent families in additive manufacturing originating in the UK between 2001 and 2020, close to France's 1,938. Additive Manufacturing UK's 2026 annual plan puts the UK market at £515m to £740m in 2024, or 3% to 4.3% of the global total, a range reflecting disagreement between estimates. Neither a patent family, which records an attempt to protect an invention, nor a market estimate, which can include machines bought overseas, says what share of the resulting production happens in Britain.
Craig Pyser, chair of AMUK and chief executive of Portsmouth-based AMufacture, calls Britain's share respectable for an economy of its size while acknowledging the old complaint that British engineers invent what others sell better. His interest is in what gives a customer a commercial reason to manufacture here, and for some buyers visiting the factory, establishing where a part came from and getting a replacement quickly already does. Researchers at Added Scientific pointed to Wayland and to Alloyed, which began in Oxford materials research, licensed a cast nickel alloy to Hitachi Metals in 2018 and sold its first flight parts from Seattle in 2023.
From grant to first customer
Jake Hand, co-founder of Exeter-based Rapid Fusion, has seen grant funding from both sides. The company grew out of equipment distributor Evo 3D and now builds large-format additive manufacturing systems; Hand says it is profitable without R&D funding and that Innovate UK support let it develop its own technology and share costs it would otherwise carry alone. His criticism concerns the moment a project works: in his words, "they back a project, but not a business." The award buys engineering time to solve a defined problem, while a customer asks whether the machine can make a particular mould, who trains the operator and what happens if it stops mid-job, and answering that for one sale can take months.
At Kingston University a £450,000 Zeus robotic cell combining large-format printing with CNC milling followed a similar route, after a graduate who had joined Rapid Fusion introduced his employer to his old department.
Who owns the spin-out
Ownership is the next obstacle. John Robinson, additive manufacturing research commercialisation manager at the University of Wolverhampton, incorporated a company in May 2017 that funded his PhD and says he and the university filed several patent applications together in 2024; his current research combines materials in devices that carry heat away from data-centre equipment. He recalls the university's former technology transfer office wanting 75% of the company, while more recent talks with its enterprise team were about a potential 10% stake. Both were proposals. The Royal Academy of Engineering and Dealroom found that, among UK deep-tech hardware spin-outs in their sample, the average non-cash stake taken by universities fell from 25% in 2015–19 to 14% in 2024–25, on partial 2025 data.
Louis Masters has crossed that threshold. Hydra Manufacturing, a University of Leeds spin-out developing equipment for technical ceramics, announced £320,000 in equity investment led by SFC Capital in March, and about £577,000 including earlier grant support; he was considering raising around £1m or more. He understands why an investor wants two more installations, since a machine on a customer's floor is a stronger signal than an encouraging email, but developing the equipment and winning those customers consumes the capital he is trying to raise. Germany, with its concentration of advanced ceramics manufacturers, is a natural early market.
The installed base
Richardson identifies what the usual commercialisation account misses: "So if you're not actually doing the doing, then you're not going to get good at it." His concern is Britain's limited installed base of industrial equipment and, in some of Wayland's markets, the shortage of major customers willing to put work through it. It shows in recruitment: an engineer from a CNC background can learn to run an additive system, but where several factories run the equipment an employer can hire someone who has already prepared builds and kept a machine productive, while with a small installed base each firm trains more itself. Paul Tickle of post-processing specialist Holdson sees the same difference in recruits who used industrial equipment during apprenticeships.
Renishaw's Ben Deary and Ed Littlewood describe what a company finds when it brings production back after years of buying overseas: it can commission a machine and hire operators only to discover that a supplier it once relied on for a component or a service has gone. They point to Apex Additive Technologies, a Welsh business that develops process parameters, makes the first parts and establishes that the process works, after which the customer may take production in-house. Jason Hutt of Fastech states the incumbent advantage plainly: "Casting's approved, isn't it?" An additively manufactured replacement may pass material tests and still need evidence specific to the equipment, process and grade a customer specified, and a second buyer may ask for much of the work again. The £38m, Airbus-led DECSAM programme, with Renishaw, GKN Aerospace, Apex and the Manufacturing Technology Centre, is one attempt to share that cost.
Where the customers are
CloudNC's chief operating officer, Jason Bowes, told a Manufacturing Technologies Association briefing at the House of Lords on 12 November that "it's far, far easier to sell our technology in the U.S. than it is here"; the company develops AI-assisted software for programming CNC machines and tests it in its own British factory. At AMufacture, Pyser estimates 95% to 98% of work is now production, with defence the largest sector after overtaking marine in the past year and automotive also significant. Some defence customers revise designs every six to eight weeks, so a local manufacturer able to take the revised file and deliver the next batch can earn repeat orders.
What procurement can settle
James Selka, chief executive of the Manufacturing Technologies Association, told the same briefing that investment was poised to enter British manufacturing but needed "a proper demand signal and co-investment from government", putting energy prices first among immediate obstacles. Lord Harrington of Watford, chair of Make UK, recalled that sector deals under Theresa May worked where companies could put substantial sums alongside public money, while elsewhere some businesses government wanted to encourage could scarcely afford their share; he had chaired GeoPura, a hydrogen power business sold to Canada's Ballard Power Systems in August for £275m upfront.
The team at Added Scientific draws a policy-relevant distinction: an established single-material process, where an engineer can already buy printed stainless-steel components, calls for a buyer willing to specify and accept the part, whereas multi-material or multifunctional device work may still need research funding to establish whether the device works. Procurement is where government has direct influence, as Harrington acknowledged when asked about fusion. In 2025 the UK Atomic Energy Authority commissioned two additive systems at its Central Support Facility, a Freemelt electron-beam machine for tungsten and a Nikon SLM laser system supplied by Kingsbury Machine Tools with support from Additure, and it reports British participants including Laser Additive Solutions, The Welding Institute and WAAM3D in separate fusion maintenance projects. It publishes a quarterly procurement pipeline separating possibilities one to five years out, pre-commercial work and confirmed tenders.
For Pyser, one test of the Formnext appearance is whether an overseas company looking for a European base chooses to establish it here. Smaller questions can be followed up in a year: did a customer who saw a British-built machine in Frankfurt order one, and did the first installation lead to a second? The Admiralty answered Brunel in May 1803 by ordering the machines for the smaller blocks.
